What is a balance shaft belt
Acrobat Printable VersionTools
- Jack stands
Refer to the Timing Belt Arrangement drawings below for details.
1983 - 1986 944 Timing Belt Arrangement
1987 - 1991 944 Timing Belt Arrangement
1992 - 1995 968 Timing Belt Arrangement
Initial Tensioning on Belt Installation (1983 -1986 Model Cars Without Spring Tensioner)
- Pre-tension the camshaft belt by turning the tensioning roller eccentric nut (thin 24 mm or thin 27 mm open end wrench) counter-clockwise until the belt can be twisted 90° using the thumb and forefinger. This should be checked at the midpoint between the cam sprocket and the crankshaft sprocket. Tighten the tensioning roller locknut to 45 Nm (33 ft-lbs). Apply counter-torque to the tensioning roller eccentric nut while tightening locknut to prevent altering the belt tension.
Note: Originally, this was the only method of tensioning used on 928s and 924s. I know of several shops that have never purchase Special Tool 9201 and use this method on 944s as well. However, it is very risky and I strongly recommend checking the belt with the factory tensioning gage.
Belt Tensioning (1987 Model and Newer Cars With Spring Tensioner)
- Release the spring tensioner by loosening the locking nut and locking bolt near the spring end of the tensioner.
- Tighten the locking bolt and locknut to 20 Nm (15 ft-lbs).
Checking and Adjusting Cam Belt Tension (All Cars)
Yes, all cars. While some people contend that the tension does not need to be checked on cars with spring tensioners, I would disagree. From experience, I've found that spring tensioners vary from car to car and will not apply the same tension consistently when the spring is released. The spring tensioners seem to get close enough to the 2.7 ±0.3 spec for a used belt to be of little concern. However, the spring tensioner WILL NOT tension a new belt to within the tolerance for a new belt (4.0 ±0.3) unless the spring is released, the engine is rolled a degree or two, and then the tensioner is tightened down. The problem is that since spring tensioners tend to vary, you don't know exactly how many degrees to roll the engine. That's why it's important to check the tension using Special Tool 9201.
- After the camshaft belt has been pre-tensioned, remove the flywheel lock if installed.
Do not install starter until crankshaft bolt is installed and torqued as the flywheel lock will need to be installed again.
When checking timing belt tension, the timing belt tool is installed such that the gauge on the tool is oriented upside
down. It also requires the flat bars on the tool to slide between the timing belt and the timing belt cover which is a snug fit. This is perfectly acceptable.
- Tension specs:
- New belt - 4.0 ±0.3
Used belt - 2.7 ±0.3
- Adjust the belt tension by loosening the tensioning roller locknut and turning the tensioning roller eccentric nut (thin 24 or thin 27 mm open end wrench) counter-clockwise and tighten locknut. Apply counter-torque to the eccentric roller when tightening locknut to prevent altering torque.
Repeat the steps above until the cam belt tension is within the specified tolerance. Torque tensioner locknut to 45 Nm (33 ft-lbs).
- On the front plate of the spring tensioner there are three fasteners. One holds the roller in the tensioner. The other two are used to tension the belt. To tension the belt, simply loosen the lock nut on the pivot arm (top fastener) and the locking bolt (lower). You'll notice a slot behind the head on the lock bolt. Loosening the lock nut and bolt allows the tension to be released on the spring to retension the belt. Using a pry bar or balance shaft pin spanner, you may want to gently nudge the tensioner in release direction (i.e. more tension on the belt). Sometimes after sitting for a while the spring tensioners like to stick. Once you're satisfied that the tensioner has released, tighten the tensioner lock nut/bolt. Spring tensioners tend to be a bit unreliable as far as consistency in tensioning. I recommend checking the tension with the factory tool, the twist method (described previously in this procedure), or with an aftermarket tension tool (i.e. Optibelt, Market, etc.)
The intended tool for this purpose is the balance shaft sprocket pin spanner (P9200). The spanner pins fit into two holes on the front of the spring tensioner body.
Balance Shaft Belt Tensioning (All Cars)
- Determine the amount of belt tension required for the type of belt you have.
- Old style belt (15 mm wide) - 2.7 ± 0.3
New style belt (18 mm wide) - 3.5 ± 0.5
If you have someone to help you it is possible to adjust the belt tension while the tensioning gage is installed. However, the tension should be checked again after the tensioning roller locknut is torqued.